What oil do I Need for my van?

Whether you are a DIY mechanic or an automotive enthusiast, knowing what kind of oil your van needs is essential to its upkeep and performance. This article serves as a comprehensive guide to help you determine the right oil for your van. 

ScrapVan123 provides all the information you need to make an informed decision on which oil will work best for your particular van, so that it can stay running at peak performance.

Different Types of Oils for Vans

Synthetic oil for vans

The type of oil you need to use for your van in the UK will depend on the make and model of your vehicle, as well as the engine type and age.

In general, it’s best to refer to your vehicle’s owner manual for guidance on the recommended oil type and viscosity. You can also consult with a mechanic or check with the manufacturer to ensure you’re using the correct oil for your van. In the UK, motor oils are graded according to their viscosity, which is a measure of how thick or thin the oil is. The most common types of motor oils used in the UK are 5W-30, 5W-40, and 10W-40.

Here are some of the most commonly used oils for vans:

Mineral Oil: 

Mineral oil is a basic type of motor oil that is derived from crude oil. It is the most affordable option, but it has limited performance and durability compared to synthetic oils.

Synthetic Oil: 

Synthetic oil is made using advanced chemical processes and is designed to provide superior performance and protection compared to mineral oil. Synthetic oils are more expensive than mineral oils, but they offer better engine protection, longer intervals between oil changes, and improved fuel economy.

Semi-Synthetic Oil: 

Semi-synthetic oil is a blend of mineral and synthetic oils, offering a balance between performance and affordability. Semi-synthetic oils provide better performance and protection than mineral oils, but they are not as good as full synthetic oils.

High Mileage Oil: 

This type of oil is specifically designed for older vehicles that have high mileage. It contains special additives that help to reduce oil consumption and prevent leaks, as well as condition the engine seals.

Low Viscosity Oil: 

Low viscosity oil is designed to provide better fuel economy by reducing friction and improving engine efficiency. Low viscosity oils are typically rated as 0W-20, 5W-20, or 5W-30.

Again, it’s important to refer to your vehicle’s owner manual or consult with a mechanic to determine the recommended oil type and viscosity for your specific van.

So, What oil Should I put in my van?

To determine which oil to put in your van, you should navigate to Halfords and use their handy engine oil checker tool. With the above knowledge now known and by using the reg checker to determine which type of oil is suitable for your van, you can rest assured that you are treating your van properly with the correct fluids.

Changing oil in your van: Step by Step

A mechanic changing van oil
  1. Firstly, you will need to get all the necessary tools and supplies. These tools include a new oil filter, fresh oil, a wrench or socket set, an oil drain pan, a funnel, and a rag.
  2. Secondly, park your van on a flat surface and turn off the engine. Wait for the engine to cool down before starting, and locate the oil drain plug on the underside of the engine. Position the oil drain pan beneath the plug to catch the old oil.
  3. Use a wrench or socket set to loosen the drain plug. Be careful not to burn yourself on the hot oil as it drains, and once all the old oil has drained out, replace the drain plug and tighten it securely.
  4. Nextly, locate the oil filter on the engine. You may need to use a wrench or filter wrench to remove it! Be sure to have the oil drain pan underneath to catch any drips, and apply a small amount of fresh oil to the rubber gasket on the top of the new oil filter.
  5. Screw the new oil filter onto the engine by hand, being careful not to over-tighten it, then locate the oil filler cap on top of the engine, remove it and insert the funnel.
  6. Pour in the new oil slowly and steadily, checking the oil level with the dipstick as you go, and once you’ve added the appropriate amount of oil, replace the filler cap and start the engine.
  7. Let the engine run for a few minutes to circulate the new oil throughout the engine. You should recheck the oil level with the dipstick and add more oil if necessary, however if not, dispose of the old oil and oil filter properly. You can take them to a local recycling centre or an auto parts store that accepts used oil.